Con-Serv, Inc. - Quality Slide Bearings For All Industries

Quality Slide Bearings For All Industries

Search Catalog
      GO   
 CON-SLIDE™    Type CHP (High Load)
CON-SLIDE™ > Type CHP Bearings > Type CHP (High Load) > View Items  

Type CHP (High Load)

Check up to five results to perform an action.


This bearing system utilizes the sell-lubricating, low-friction characteristics of Teflon® coupled with the high tensile strength characteristics of synthetic fibers.
The unique system employs a stainless steel upper element sliding on a CHP lower element. This two element concept has seen worldwide acceptance lor major pipeline, bridge, building and industrial applications. The system will yield long life under high load applications. This system gives the designer high pressure allowable loads even at design temperatures of 500°F.
The design engineer shall determine the square inches ot bearing area required for the lower element by dividing the load by the allowable pressure from the graph. The upper element is sized for the movement after the lower element is sized for pressure. Size is out to out of back-up plate.
For ease of installation, CON-SERV recommends a back-up plate 1" larger than the PTFE size to allow a 1/2" recess all around. This recess must be provided for plates requiring a seal weld.
This bearing system has been tested in a long cycle friction apparatus. The coefficient of friction at 70°F for the load ranges indicated varies from 4% to 5%. This variation is due to the initial break-in period, not due to the variation in pressure.
When friction was recorded at the design temperature limit of 500°F, it was 2-1/2% to 1-1/2% depending on the dwell time at 500°F. It is interesting to note that friction decreases with increases in either load or temperature.
Certifications are available on this data upon request wilh job applications.





    border="0" Printable Page  
    Email Email This Page  
    Save To Favorites Save To Favorites
  
Compare Items
   
  Results 1 - 25 of 90 1 2 3 4 

Item #

Slide Surface Thickness

Slide Surface Material

Back-Up Plate Thickness

Back-Up Plate Material

CHP Upper 03SS 13CS 20 GA Stainless Steel 10 GA Carbon Steel
CHP Upper 03SS 25CS 20 GA Stainless Steel 1/4" PL Carbon Steel
CHP Upper 03SS 37CS 20 GA Stainless Steel 3/8" PL Carbon Steel
CHP Upper 03SS 50CS 20 GA Stainless Steel 1/2" PL Carbon Steel
CHP Upper 03SS 75CS 20 GA Stainless Steel 3/4" PL Carbon Steel
CHP Upper 03SS 100CS 20 GA Stainless Steel 1" PL Carbon Steel
CHP Upper 03SS 13SS 20 GA Stainless Steel 10 GA Stainless Steel
CHP Upper 03SS 25SS 20 GA Stainless Steel 1/4" PL Stainless Steel
CHP Upper 03SS 37SS 20 GA Stainless Steel 3/8" PL Stainless Steel
CHP Upper 03SS 50SS 20 GA Stainless Steel 1/2" PL Stainless Steel
CHP Upper 03SS 75SS 20 GA Stainless Steel 3/4" PL Stainless Steel
CHP Upper 03SS 100SS 20 GA Stainless Steel 1" PL Stainless Steel
CHP Upper 03SS 13CT 20 GA Stainless Steel 10 GA Corten Steel
CHP Upper 03SS 25CT 20 GA Stainless Steel 1/4" PL Corten Steel
CHP Upper 03SS 37CT 20 GA Stainless Steel 3/8" PL Corten Steel
CHP Upper 03SS 50CT 20 GA Stainless Steel 1/2" PL Corten Steel
CHP Upper 03SS 75CT 20 GA Stainless Steel 3/4" PL Corten Steel
CHP Upper 03SS 100CT 20 GA Stainless Steel 1" PL Corten Steel
CHP Upper 03SS 13GL 20 GA Stainless Steel 10 GA Galvanized Steel
CHP Upper 03SS 25GL 20 GA Stainless Steel 1/4" PL Galvanized Steel
CHP Upper 03SS 37GL 20 GA Stainless Steel 3/8" PL Galvanized Steel
CHP Upper 03SS 50GL 20 GA Stainless Steel 1/2" PL Galvanized Steel
CHP Upper 03SS 75GL 20 GA Stainless Steel 3/4" PL Galvanized Steel
CHP Upper 03SS 100GL 20 GA Stainless Steel 1" PL Galvanized Steel
CHP Upper 03SS 13AL 20 GA Stainless Steel 10 GA Aluminum
  Results 1 - 25 of 90 1 2 3 4 
  

Con-Serv, Inc.
Quality • Service • Economy

1-800-541-1044 / Fax 843-546-1055
685 Aviation Blvd. • Georgetown, SC 29440