Con-Serv, Inc. - Quality Slide Bearings For All Industries

Quality Slide Bearings For All Industries

Search Catalog
      GO   
 CON-SLIDE™    Type CSA (75 PSI to 2000 PSI)
CON-SLIDE™ > Type CSA & CSB Bearings > Type CSA (75 PSI to 2000 PSI) > View Items  

Type CSA (75 PSI to 2000 PSI)

Check up to five results to perform an action.


This blend (CSA) was formulated for use against itself as a slide material.
The CSA system consists of an upper and lower element. The PTFE slide surfaces in this system are nominally 3/32" thick and are control-bonded to a 10-gauge carbon steel (CS) back up sheet. Normally the upper element is larger lhan the lower element by the amount of anticipated movement.
The blended CSA material used for this bearing is composed of virgin (unreprocessed) PTFE resin tested per ASTM D4894 or ASTM D4895 and reinforcing agents including milled glass fibers. This structural material has the following representative mechanical and physical properties:
  • Tensile Strength: 2200 psi
  • Elongation: 225%
  • Specific Gravity: 2.17-2.22
  • Actual values per lot are available upon request which might vary due to processing factors.
    The design engineer shall determine the square inches of bearing area required for the lower element by dividing the load by the allowable pressure from the graph. The upper element is sized for the movement after the lower element is sized for load.
    CON-SERV Inc can supply any practical size cut from stock steel. Size is out to out of back-up plate.
    For ease of installation, CON-SERV recommends a back-up plate 1" larger than the CSA or CSB size to allow a 1/2" recess all around. This recess must be provided for plates requiring a seal weld.
    Certifications on the epoxy, steel and CSA material are available upon request.





        border="0" Printable Page  
        Email Email This Page  
        Save To Favorites Save To Favorites
      
    Compare Items
       
      Results 1 - 25 of 120 1 2 3 4 5 

    Item #

    Slide Surface Thickness

    Slide Surface Material

    Back-Up Plate Thickness

    Back-Up Plate Material

    CSA Upper 09CSA 13CS 3/32" CSA 10 GA Carbon Steel
    CSA Upper 09CSA 25CS 3/32" CSA 1/4" PL Carbon Steel
    CSA Upper 09CSA 37CS 3/32" CSA 3/8" PL Carbon Steel
    CSA Upper 09CSA 50CS 3/32" CSA 1/2" PL Carbon Steel
    CSA Upper 09CSA 75CS 3/32" CSA 3/4" PL Carbon Steel
    CSA Upper 09CSA 100CS 3/32" CSA 1" PL Carbon Steel
    CSA Lower 09CSA 13CS 3/32" CSA 10 GA Carbon Steel
    CSA Lower 09CSA 25CS 3/32" CSA 1/4" PL Carbon Steel
    CSA Lower 09CSA 37CS 3/32" CSA 3/8" PL Carbon Steel
    CSA Lower 09CSA 50CS 3/32" CSA 1/2" PL Carbon Steel
    CSA Lower 09CSA 75CS 3/32" CSA 3/4" PL Carbon Steel
    CSA Lower 09CSA 100CS 3/32" CSA 1" PL Carbon Steel
    CSA Upper 09CSA 13SS 3/32" CSA 10 GA Stainless Steel
    CSA Upper 09CSA 25SS 3/32" CSA 1/4" PL Stainless Steel
    CSA Upper 09CSA 37SS 3/32" CSA 3/8" PL Stainless Steel
    CSA Upper 09CSA 50SS 3/32" CSA 1/2" PL Stainless Steel
    CSA Upper 09CSA 75SS 3/32" CSA 3/4" PL Stainless Steel
    CSA Upper 09CSA 100SS 3/32" CSA 1" PL Stainless Steel
    CSA Lower 09CSA 13SS 3/32" CSA 10 GA Stainless Steel
    CSA Lower 09CSA 25SS 3/32" CSA 1/4" PL Stainless Steel
    CSA Lower 09CSA 37SS 3/32" CSA 3/8" PL Stainless Steel
    CSA Lower 09CSA 50SS 3/32" CSA 1/2" PL Stainless Steel
    CSA Lower 09CSA 75SS 3/32" CSA 3/4" PL Stainless Steel
    CSA Lower 09CSA 100SS 3/32" CSA 1" PL Stainless Steel
    CSA Upper 09CSA 13CT 3/32" CSA 10 GA Corten Steel
      Results 1 - 25 of 120 1 2 3 4 5 
      

    Con-Serv, Inc.
    Quality • Service • Economy

    1-800-541-1044 / Fax 843-546-1055
    685 Aviation Blvd. • Georgetown, SC 29440