Products Catalog

This blend (CSA) was formulated for use against itself as a slide material.
The CSA system consists of an upper and lower element. The PTFE slide surfaces in this system are nominally 3/32" thick and are control-bonded to a 10-gauge carbon steel (CS) back up sheet. Normally the upper element is larger than the lower element by the amount of anticipated movement.
The blended CSA material used for this bearing is composed of virgin (unreprocessed) PTFE resin tested per ASTM D4894 or ASTM D4895 and reinforcing agents including milled glass fibers. This structural material has the following representative mechanical and physical properties:
  • Tensile Strength: 2200 psi
  • Elongation: 225%
  • Specific Gravity: 2.17-2.22
Actual values per lot are available upon request which might vary due to processing factors.
The design engineer shall determine the square inches of bearing area required for the lower element by dividing the load by the allowable pressure from the graph. The upper element is sized for the movement after the lower element is sized for load.
CON-SERV Inc can supply any practical size cut from stock steel. Size is out to out of back-up plate.
For ease of installation, CON-SERV recommends a back-up plate 1" larger than the CSA or CSB size to allow a 1/2" recess all around. This recess must be provided for plates requiring a seal weld.
Certifications on the epoxy, steel and CSA material are available upon request.
1 - 25 of 120 | Results Per Page | View | Unit of Measure
1 2 3 4 5 

Item #

Slide Surface Thickness

Slide Surface Material

Back-Up Plate Thickness

Back-Up Plate Material

Quantity
N/A 3/32" N/A CSA N/A 10 GA N/A Carbon Steel
N/A 3/32" N/A CSA N/A 1/4" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 3/8" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 1/2" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 3/4" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 1" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 10 GA N/A Carbon Steel
N/A 3/32" N/A CSA N/A 1/4" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 3/8" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 1/2" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 3/4" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 1" PL N/A Carbon Steel
N/A 3/32" N/A CSA N/A 10 GA N/A Stainless Steel
N/A 3/32" N/A CSA N/A 1/4" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 3/8" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 1/2" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 3/4" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 1" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 10 GA N/A Stainless Steel
N/A 3/32" N/A CSA N/A 1/4" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 3/8" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 1/2" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 3/4" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 1" PL N/A Stainless Steel
N/A 3/32" N/A CSA N/A 10 GA N/A Corten Steel
1 - 25 of 120 | Results Per Page | View | Unit of Measure
1 2 3 4 5