Products Catalog

This blend (CSB) was formulated for use against a smooth stainless steel surface.
The CSB system consists of an upper and lower element. The PTFE surface (1 only) is on the lower element. It is nominally 1/16" thick and is control-bonded to a 10-gauge carbon steel (CS) back-up sheet. The upper element is composed of a 20-gauge stainless steel (SS) sheet (RMS<20) resistance welded to a 10-gauge carbon steel (CS) back-up sheet.
The blended CSB material used for this bearing is composed of virgin (unreprocessed) PTFE resin tested per ASTM D4894 or ASTM D4895 and reinforcing agents including milled glass fibers. This structural material has the following representative mechanical and physical properties:
  • Tensile Strength: 3300 psi
  • Elongation: 300%
  • Specific Gravity: 2.14 - 2.21
Actual values per lot are available upon request which might vary due to processing factors.
The design engineer shall determine the square inches of bearing area required for the lower element by dividing the load by the allowable pressure from the graph. The upper element is sized for the movement after the lower element is sized for load.
CON-SERV Inc can supply any practical size cut from stock steel. Size is out to out of back-up plate.
For ease of installation, CON-SERV recommends a back-up plate 1" larger than the CSA or CSB size to allow a 1/2" recess all around. This recess must be provided for plates requiring a seal weld.
Certifications on the epoxy, steel and CSB material are available upon request.
1 - 25 of 120 | Results Per Page | View | Unit of Measure
1 2 3 4 5 

Item #

Slide Surface Thickness

Slide Surface Material

Back-Up Plate Thickness

Back-Up Plate Material

Quantity
CSB Upper 03SS 13CS N/A 20 GA N/A Stainless Steel N/A 10 GA N/A Carbon Steel
CSB Upper 03SS 25CS N/A 20 GA N/A Stainless Steel N/A 1/4" PL N/A Carbon Steel
CSB Upper 03SS 37CS N/A 20 GA N/A Stainless Steel N/A 3/8" PL N/A Carbon Steel
CSB Upper 03SS 50CS N/A 20 GA N/A Stainless Steel N/A 1/2" PL N/A Carbon Steel
CSB Upper 03SS 75CS N/A 20 GA N/A Stainless Steel N/A 3/4" PL N/A Carbon Steel
CSB Upper 03SS 100CS N/A 20 GA N/A Stainless Steel N/A 1" PL N/A Carbon Steel
CSB Upper 03SS 13SS N/A 20 GA N/A Stainless Steel N/A 10 GA N/A Stainless Steel
CSB Upper 03SS 25SS N/A 20 GA N/A Stainless Steel N/A 1/4" PL N/A Stainless Steel
CSB Upper 03SS 37SS N/A 20 GA N/A Stainless Steel N/A 3/8" PL N/A Stainless Steel
CSB Upper 03SS 50SS N/A 20 GA N/A Stainless Steel N/A 1/2" PL N/A Stainless Steel
CSB Upper 03SS 75SS N/A 20 GA N/A Stainless Steel N/A 3/4" PL N/A Stainless Steel
CSB Upper 03SS 100SS N/A 20 GA N/A Stainless Steel N/A 1" PL N/A Stainless Steel
CSB Upper 03SS 13CT N/A 20 GA N/A Stainless Steel N/A 10 GA N/A Corten Steel
CSB Upper 03SS 25CT N/A 20 GA N/A Stainless Steel N/A 1/4" PL N/A Corten Steel
CSB Upper 03SS 37CT N/A 20 GA N/A Stainless Steel N/A 3/8" PL N/A Corten Steel
CSB Upper 03SS 50CT N/A 20 GA N/A Stainless Steel N/A 1/2" PL N/A Corten Steel
CSB Upper 03SS 75CT N/A 20 GA N/A Stainless Steel N/A 3/4" PL N/A Corten Steel
CSB Upper 03SS 100CT N/A 20 GA N/A Stainless Steel N/A 1" PL N/A Corten Steel
CSB Upper 03SS 13GL N/A 20 GA N/A Stainless Steel N/A 10 GA N/A Galvanized Steel
CSB Upper 03SS 25GL N/A 20 GA N/A Stainless Steel N/A 1/4" PL N/A Galvanized Steel
CSB Upper 03SS 37GL N/A 20 GA N/A Stainless Steel N/A 3/8" PL N/A Galvanized Steel
CSB Upper 03SS 50GL N/A 20 GA N/A Stainless Steel N/A 1/2" PL N/A Galvanized Steel
CSB Upper 03SS 75GL N/A 20 GA N/A Stainless Steel N/A 3/4" PL N/A Galvanized Steel
CSB Upper 03SS 100GL N/A 20 GA N/A Stainless Steel N/A 1" PL N/A Galvanized Steel
CSB Upper 03SS 13AL N/A 20 GA N/A Stainless Steel N/A 10 GA N/A Aluminum
1 - 25 of 120 | Results Per Page | View | Unit of Measure
1 2 3 4 5