Con-Serv, Inc. - Quality Slide Bearings For All Industries

Quality Slide Bearings For All Industries

Search Catalog
      GO   
 CON-SLIDE™    Type CSB (2000 PSI to 4000 PSI)
CON-SLIDE™ > Type CSA & CSB Bearings > Type CSB (2000 PSI to 4000 PSI) > View Items  

Type CSB (2000 PSI to 4000 PSI)

Check up to five results to perform an action.


This blend (CSB) was formulated for use against a smooth stainless steel surface.
The CSB system consists of an upper and lower element. The PTFE surface (1 only) is on the lower element. It is nominally 1/16" thick and is control-bonded to a 10-gauge carbon steel (CS) back-up sheet. The upper element is composed of a 20-gauge stainless steel (SS) sheet (RMS<20) resistance welded to a 10-gauge carbon steel (CS) back-up sheet.
The blended CSB material used for this bearing is composed of virgin (unreprocessed) PTFE resin tested per ASTM 04894 or ASTM D4895 and reinforcing agents including milled glass fibers. This structural material has the following representative mechanical and physical properties:
  • Tensile Strength: 3300 psi
  • Elongation: 300%
  • Specific Gravity: 2.11 - 2.21
    Actual values per lot are available upon request which might vary due to processing factors.
    The design engineer shall determine the square inches of bearing area required for the lower element by dividing the load by the allowable pressure from the graph. The upper element is sized for the movement after the lower element is sized for load.
    CON-SERV Inc can supply any practical size cut from stock steel. Size is out to out of back-up plate.
    For ease of installation, CON-SERV recommends a back-up plate 1" larger than the CSA or CSB size to allow a 1/2" recess all around. This recess must be provided for plates requiring a seal weld.
    Certifications on the epoxy, steel and CSB material are available upon request. Welded to a 10-gauge carbon steel (CS) back-up sheet.




  •     border="0" Printable Page  
        Email Email This Page  
        Save To Favorites Save To Favorites
      
    Compare Items
       
      Results 76 - 100 of 120 1 2 3 4 5 

    Item #

    Slide Surface Thickness

    Slide Surface Material

    Back-Up Plate Thickness

    Back-Up Plate Material

    CSB Lower 06CSB 50CT 1/16" CSB 1/2" PL Corten Steel
    CSB Lower 06CSB 75CT 1/16" CSB 3/4" PL Corten Steel
    CSB Lower 06CSB 100CT 1/16" CSB 1" PL Corten Steel
    CSB Lower 06CSB 13GL 1/16" CSB 10 GA Galvanized Steel
    CSB Lower 06CSB 25GL 1/16" CSB 1/4" PL Galvanized Steel
    CSB Lower 06CSB 37GL 1/16" CSB 3/8" PL Galvanized Steel
    CSB Lower 06CSB 50GL 1/16" CSB 1/2" PL Galvanized Steel
    CSB Lower 06CSB 75GL 1/16" CSB 3/4" PL Galvanized Steel
    CSB Lower 06CSB 100GL 1/16" CSB 1" PL Galvanized Steel
    CSB Lower 06CSB 13AL 1/16" CSB 10 GA Aluminum
    CSB Lower 06CSB 25AL 1/16" CSB 1/4" PL Aluminum
    CSB Lower 06CSB 37AL 1/16" CSB 3/8" PL Aluminum
    CSB Lower 06CSB 50AL 1/16" CSB 1/2" PL Aluminum
    CSB Lower 06CSB 75AL 1/16" CSB 3/4" PL Aluminum
    CSB Lower 06CSB 100AL 1/16" CSB 1" PL Aluminum
    CSC Lower 06CSC 13CS 1/16" CSC 10 GA Carbon Steel
    CSC Lower 06CSC 25CS 1/16" CSC 1/4" PL Carbon Steel
    CSC Lower 06CSC 37CS 1/16" CSC 3/8" PL Carbon Steel
    CSC Lower 06CSC 50CS 1/16" CSC 1/2" PL Carbon Steel
    CSC Lower 06CSC 75CS 1/16" CSC 3/4" PL Carbon Steel
    CSC Lower 06CSC 100CS 1/16" CSC 1" PL Carbon Steel
    CSC Lower 06CSC 13SS 1/16" CSC 10 GA Carbon Steel
    CSC Lower 06CSC 25SS 1/16" CSC 1/4" PL Stainless Steel
    CSC Lower 06CSC 37SS 1/16" CSC 3/8" PL Stainless Steel
    CSC Lower 06CSC 50SS 1/16" CSC 1/2" PL Stainless Steel
      Results 76 - 100 of 120 1 2 3 4 5 
      

    Con-Serv, Inc.
    Quality • Service • Economy

    1-800-541-1044 / Fax 843-546-1055
    685 Aviation Blvd. • Georgetown, SC 29440