Type CSB (2000 PSI to 4000 PSI)
Type CSA & CSB Bearings
This blend (CSB) was formulated for use against a smooth stainless steel surface.
The CSB system consists of an upper and lower element. The PTFE surface (1 only) is on the lower element. It is nominally 1/16" thick and is control-bonded to a 10-gauge carbon steel (CS) back-up sheet. The upper element is composed of a 20-gauge stainless steel (SS) sheet (RMS<20) resistance welded to a 10-gauge carbon steel (CS) back-up sheet.
The blended CSB material used for this bearing is composed of virgin (unreprocessed) PTFE resin tested per ASTM D4894 or ASTM D4895 and reinforcing agents including milled glass fibers. This structural material has the following representative mechanical and physical properties:
The design engineer shall determine the square inches of bearing area required for the lower element by dividing the load by the allowable pressure from the graph. The upper element is sized for the movement after the lower element is sized for load.
CON-SERV Inc can supply any practical size cut from stock steel. Size is out to out of back-up plate.
For ease of installation, CON-SERV recommends a back-up plate 1" larger than the CSA or CSB size to allow a 1/2" recess all around. This recess must be provided for plates requiring a seal weld.
Certifications on the epoxy, steel and CSB material are available upon request.
The CSB system consists of an upper and lower element. The PTFE surface (1 only) is on the lower element. It is nominally 1/16" thick and is control-bonded to a 10-gauge carbon steel (CS) back-up sheet. The upper element is composed of a 20-gauge stainless steel (SS) sheet (RMS<20) resistance welded to a 10-gauge carbon steel (CS) back-up sheet.
The blended CSB material used for this bearing is composed of virgin (unreprocessed) PTFE resin tested per ASTM D4894 or ASTM D4895 and reinforcing agents including milled glass fibers. This structural material has the following representative mechanical and physical properties:
- Tensile Strength: 3300 psi
- Elongation: 300%
- Specific Gravity: 2.14 - 2.21
The design engineer shall determine the square inches of bearing area required for the lower element by dividing the load by the allowable pressure from the graph. The upper element is sized for the movement after the lower element is sized for load.
CON-SERV Inc can supply any practical size cut from stock steel. Size is out to out of back-up plate.
For ease of installation, CON-SERV recommends a back-up plate 1" larger than the CSA or CSB size to allow a 1/2" recess all around. This recess must be provided for plates requiring a seal weld.
Certifications on the epoxy, steel and CSB material are available upon request.
Item # |
Slide Surface Thickness |
Slide Surface Material |
Back-Up Plate Thickness |
Back-Up Plate Material |
Quantity |
---|---|---|---|---|---|
CSB Lower 06CSB 37CS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Carbon Steel | |
CSB Lower 06CSB 37SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Stainless Steel | |
CSB Lower 06CSB 37CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Corten Steel | |
CSB Lower 06CSB 37GL | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Galvanized Steel | |
CSB Lower 06CSB 37AL | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Aluminum | |
CSC Lower 06CSC 37CS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSC | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Carbon Steel | |
CSC Lower 06CSC 37SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSC | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Stainless Steel | |
CSC Lower 06CSC 37CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSC | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Corten Steel | |
CSC Lower 06CSC 37GL | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSC | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Galvanized Steel | |
CSC Lower 06CSC 37AL | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSC | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Aluminum | |
CSB Upper 03SS 50CS | Slide Surface Thickness N/A 20 GA | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Carbon Steel | |
CSB Upper 03SS 50SS | Slide Surface Thickness N/A 20 GA | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Stainless Steel | |
CSB Upper 03SS 50CT | Slide Surface Thickness N/A 20 GA | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Corten Steel | |
CSB Upper 03SS 50GL | Slide Surface Thickness N/A 20 GA | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Galvanized Steel | |
CSB Upper 03SS 50AL | Slide Surface Thickness N/A 20 GA | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Aluminum | |
CSB Upper 06SS 50CS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Carbon Steel | |
CSB Upper 06SS 50SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Stainless Steel | |
CSB Upper 06SS 50CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Corten Steel | |
CSB Upper 06SS 50GL | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Galvanized Steel | |
CSB Upper 06SS 50AL | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A Stainless Steel | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Aluminum | |
CSB Lower 06CSB 50CS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Carbon Steel | |
CSB Lower 06CSB 50SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Stainless Steel | |
CSB Lower 06CSB 50CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Corten Steel | |
CSB Lower 06CSB 50GL | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Galvanized Steel | |
CSB Lower 06CSB 50AL | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSB | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Aluminum |